You are understanding how this works now. Yes, these machine can be thought of as electron concentrators, like a high pressure electron pump.

Now get this: the machine is easier to spin under load 😅.

When you don't have a load drawing current, the charge concentration starts to make back pressure that you can feel in the wheel, when you relieve the back pressure by providing a load, the machine spins easier.

So when you make one of these, you can spin it unloaded and find out the maximum physical resistance to turning by forcing the machine to short circuit.

This is why I know for a fact I have overunity, that maximum physical resistance is nothing.

Like I know it isn't litterally nothing, but I can't feel the difference when I spin the little 10 mm drive shaft with my fingers, I litterally can't feel the difference between it working with electrode on it vs it working without electrode on it.

After the glue messed up my machine I spun it with a recycled 48 watt fan motor from an old walmart house fan.

The drive shaft is all messed up and crooked and the bearings are shot, so I took the fan apart because it was shaking like pain mixer and I've had the motor lying around for a year. Any ways, if I held it at the right angle and let it vibrate my hand a bit I could line it up right with a printed fitting to spin the machine.

It did, at first it was a little slow, then when I lined everything up perfect and the speed picked up, the vibrations became easier to hold and I was able to keep the tip of the output shafter steadier to drive shaft and I must have spun the barrel at like twice the speed the drill made it go.

I did that after my barrel got ruined just to see if the motor could spin it.

If it can spin it with the electrodes in place, even if the barrel is shorted, that means it can spin it when the barrel is not shorted to me because I cannot feel the difference between working and not working in terms of resistance to spinning.

The new barrel is even better, the plates stick out of the surface of the barrel by a bit, so the electrodes don't need to contact the barrel in between plates, it'll be even easier to spin.

You are understanding how this works now. Yes, these machine can be thought of as electron concentrators, like a high pressure electron pump.

Now get this: the machine is easier to spin under load 😅.

When you don't have a load drawing current, the charge concentration starts to make back pressure that you can feel in the wheel, when you relieve the back pressure by providing a load, the machine spins easier.

So when you make one of these, you can spin it unloaded and find out the maximum physical resistance to turning by forcing the machine to short circuit.

This is why I know for a fact I have overunity, that maximum physical resistance is nothing.

Like I know it isn't litterally nothing, but I can't feel the difference when I spin the little 10 mm drive shaft with my fingers, I litterally can't feel the difference between it working with electrode on it vs it working without electrode on it.

After the glue messed up my machine I spun it with a recycled 48 watt fan motor from an old walmart house fan.

The drive shaft is all messed up and crooked and the bearings are shot, so I took the fan apart because it was shaking like pain mixer and I've had the motor lying around for a year. Any ways, if I held it at the right angle and let it vibrate my hand a bit I could line it up right with a printed fitting to spin the machine.

It did, at first it was a little slow, then when I lined everything up perfect and the speed picked up, the vibrations became easier to hold and I was able to keep the tip of the output shafter steadier to drive shaft and I must have spun the barrel at like twice the speed the drill made it go.

I did that after my barrel got ruined just to see if the motor could spin it.

If it can spin it with the electrode in place, even if the barrel is shorted, that means it can spin it when the barrel is not shorted to me because I cannot feel the difference between working and not working in terms of resistance to spinning.

You are understanding how this works now. Yes, these machine can be thought of as electron concentrators, like a high pressure electron pump.

Now get this: the machine is easier to spin under load 😅.

When you don't have a load drawing current, the charge concentration starts to make back pressure that you can feel in the wheel, when you relieve the back pressure by providing a load, the machine spins easier.

So when you make one of these, you can spin it unloaded and find out the maximum physical resistance to turning by forcing the machine to short circuit.

This is why I know for a fact I have overunity, that maximum physical resistance is nothing.